How To Measure For Window Screens

The most common and easiest way of properly measuring for a replacement screen is to utilize your existing screen. Tape the width, length so the thickness of frame and provide these exact measurements to us. Make up one's mind which, if any, hardware or screen clips are needed and where they are located on the window screen. Knowing which side the clips are located and how far from the border of screen is important to note.

Similar almost homes, your window screens sizes will vary throughout your firm. Determining how to mensurate starts with the existing windows yous would like to replace with new screens. One of the almost common types of window screens are the spring loaded screens. In that location is a certain method of how to measure for a jump loaded window screen. Please note that the tabs will go on opposite side of the tension springs. Springs go on the side where the screen fits into the deepest aqueduct of the actual window frame.

Window Screen Measuring Guide

---

Step 1: Measure out The Width

Identify your screen on a workbench or any flat surface. Adjacent, use a standard tape measure to measure out the width of your screen (left to correct). Please mensurate from the corner and not the distance between the center. This is very of import to aquire a truthful measure considering some screens can have a bow in the frame due to either damage, misuse or the screen material being too tight. Measuring from the corners volition insure your new replacement screen will fit into the windowsill perfectly.

If measuring an existing screen:

1. Offset, advisedly remove the screen from the window channel
2. Using a tape measure, record the measurement from left to right at the top
3. Adjacent, utilize the same measuring method and measure from left to correct at the lesser.
4. So, provide usa with the smaller of the ii measurements you lot recorded. This volition be your width measurement.

If measuring without a screen:

1. Using a tape mensurate, identify it in the top left channel and measure out the distance to the right channel
2. Adjacent, measure the bottom width by measuring from left to right. Be sure to place your tape measure inside the channel where the screen will rest.
3. At present that yous have 2 measurements, left record the smaller of the two and employ this as your width measurement for the adjacent footstep.
4. Lastly, you will need to subtract an ane/8" from your measurement to allow for clearance for installation.
   1. Example #1: (28 1/2" - one/8" = 28 3/8")
   2. Example #2: (32" - 1/8" = 31 vii/8")

NOTE: If using flat tension springs as hardware on LEFT or RIGHT of the frame - we recommend subtracting an additional 1/eight for the spring clearance. So your total start would be a 1/4" from your original recorded measurement.

---

Step 2: Measure The Pinnacle

Using your tape mensurate, permit'south measure the screens height by measuring from the bottom to the top. Make sure to measure your screen from the exterior of the frame. Nosotros recommend that yous avoid measuring from the center of your screen, instead mensurate from the bottom corner to the corner directly in a higher place (i.e: bottom right to height right).

If measuring an existing screen:

1. First, carefully remove the screen from the window channel
2. Using a tape measure, tape the measurement from top to lesser at the left
3. Next, apply the same measuring method and measure from meridian to bottom at the correct.
4. Then, provide us with the smaller of the two measurements you recorded. This will exist your acme measurement.

If measuring without a screen:

1. Using a tape measure, identify it in the top left channel behind the top lip and measure out the distance to the bottom left aqueduct
2. Side by side, measure the right elevation past measuring from peak to bottom. Be sure to identify your tape measure out backside the lip at the top where the screen will rest.
3. At present that you have 2 measurements, left record the smaller of the two and use this as your height measurement for the next pace.
4. Lastly, you lot volition need to decrease an one/8" from your measurement to allow for clearance for installation.
   1. Case #1: (28 ane/2" - 1/8" = 28 3/8")
   2. Instance #2: (32" - 1/8" = 31 vii/viii"
   
   

Annotation: If using flat tension springs equally hardware on TOP or Bottom of the frame - we recommend subtracting an additional 1/8 for the spring clearance. Then your full kickoff would exist a ane/4" from your original recorded measurement.

---

Step 3: Measure The Frame Thickness

The thickness of your aluminum screen. Window screens frames are avaliable in three dissimilar sizes v/16", iii/8" or 7/xvi", this is an manufacture standard. 5/16" thickness is the nearly pop over both 3/8" and vii/16". Brand sure you measure out your window frame "tracks" normally constitute on the left and correct side of the frame. Also, you should run across one or two grooves on the bottom of your window frame. Brand sure the size of your tracks or grooves volition allow the frame thickness yous choose will fit. Recall, there are literally hundreds of window frame manufacturer'due south, so it is difficult to explain all of the variations. If you know the manufacturer/brand of you window and the style/part #, it is always adept to give them a call to verify what size frame depth/thickness you lot should cull. If all else fails, choose the thinnest and go with 5/16" which is the most popular also!

Step 4: Hardware Configuration & Notes

If your screen has pull tabs, you will want to measure the distance betwixt the inside corner and the outter most part of the tabs. If y'all do not specify the location, we will place your tabs to industry standards - 6 inches from the inside corner. This method is as well used for measuring the placement of plungers and acorn latches. As for the springs, they are attached to the corner of the frame before joining the frame pieces together.

Notation: The the hardware inset measurements should be notated on the "Hardware Comments" on the product configuration page. Use this area to depict in detail where we should install your additional screen hardware. If you need farther help, experience costless to call our friendly customer service during normal concern hours.

Source: https://windowscreenpros.com/measuring-guides/how-to-measure-a-window-screen/

Posted by: harperwinfory49.blogspot.com

Share this post